Lakewood Automation

 


Office : (440) 808-4820
Fax : (440) 899-0493
Toll-Free : (800) 875-4820

Previous Tech Connects

Tech-Connect

  • Omron NS8 to AB MicroLogix 1000 1761-L32BWA
    How to set-up the communications in the Omron NS-Series HMI Touch Screen to Allen-Bradley MicroLogix 1000 PLC.
  • Omron NS8 to AB SLC503 1747-L531
    How to set-up the communications in the Omron NS-Series HMI Touch Screen to Allen-Bradley SLC 5/03 PLC.
  • Omron NS8 to AB CompactLogix 1769-L32E
    How to set-up the communications in the Omron NS-Series HMI Touch Screen to Allen-Bradley CompactLogix PLC.
  • Omron CJ1W-TC002 Setup
    How to set up writing the set point temperature, monitoring the current temperature, and setting up the PID Auto tuning.
  • Omron Trajexia FINS UDP Commands
    How to set-up UDP FINS commands to adjust the VR variables of the Trajexia motion controller & read inputs and write outputs.
  • Omron CJ1W-CT021 High Speed Counter
    How to configure the CJ1W-CT021 to use the high speed counter 0 to turn on the digital outputs on the card itself without monitoring the position in the PLC.
  • Proface Pass Thru to Omron PLC
    how to set-up the Pass-Thru Function from a Pro-Face touch screen to Omron PLC.
  • Omron CJ1 PLC Easy Backup
    How to use the Easy Backup feature in an Omron CJ1 series, using a Compact Flash card and DIP Switches.
  • Omron CP1H-Y to Smart Step Drive
    How to configure an Omron CP1H-Y PLC to an Omron Smart Step stepper drive.
  • Omron CP1L-L14 High Speed Counter to NS5
    How to configure the CP1L-L14 to use the high speed counter 0 to measure the length of material passing by a sensor. The total length is then displayed on the NS5 operator interface.
  • Omron CJ1 Ethernet PLC To Omron NS HMI Ethernet
    How to configure the Omron CJ1 PLC and Omron NS operator interface so they can communicate to each other over Ethernet. This will also show how to setup the required Routing Tables in CX-Integrator.
  • Yaskawa V7 Encoder as Frequency Reference
    How to configure a V7 to use an Encoder or pulses, as the frequency reference of the drive.
  • CJ1M-CPU11-ETN to CQM1H Controller Link
    How to configure the CQM1H and the CJ1M-CPU11-ETN so that data can be transferred over the Controller Link Network. It will also show how to go online with the CQM1H while be physically connected to the CJ1M over the Controller Link network.
  • ProFace AGP3560T Video Demo - This document will show how to configure a ProFace AGP 3560T to view a video from a CF card, to record a video to a CF card, and use the event recorder to record video to a CF card.
  • Advantech ADAM4055 IO Module To Proface AGP3560T via Modbus RTU - This document will show how to configure an ADAM 4055 8 Digital In and 8 Digital out Modbus RTU module to communicate with a ProFace AGP Operator Interface.
  • Omron CJ1 PDC15 - This document will show how to configure the Omron CJ1W PDC15 Isolated type Direct Current Input Unit.
  • Proface AGP to Microscan Barcode Reader - This document will show how to configure a Pro-Face AGP 3560T to receive a barcode from a Microscan Quadrus Mini from the RS-232 port.
  • Proface AGP to Omron CJ1M Ethernet - This document will show how to configure AGP3200T using GpProEx V2.0 to communicate over Ethernet to an Omron CJ1 Ethernet Adapter (ETN Module) using CX-Programmer V7.0.
  • FTP via an Omron CJ1 Ethernet Port - This document will show how to configure a CJ1W-ETN21 or the Built in Ethernet port on the CJ1M CPU to be able to act as an FTP server so you can access the information on the Memory Card.
  • Xycom AGP to Wago Ethernet IO - This document will show how to configure AGP3400T to be the Master, and Wago Modbus TCP Ethernet to be the Slave.
  • Xycom AGP to Omron E5ZN - This document will show how to configure the Xycom AGP-3400T and an Omron E5ZN Temperature Controller to pass data over Compo Way/F 2 Wire RS485.
  • Xycom AGP to Yaskawa V7 Modbus - This document will show how to configure the AGP3400T in GP PRO EX and how to setup the V7 inverter so the touch screen can be used to start and stop the drive and also set the frequency.
  • Xycom GP Pro Ex Recipe Setup - This document will show how to configure the Recipes, Filing Data and CSV Data in the GP Pro Ex software for use with a Xycom AGP-3400T and an Omron SRM1 PLC.
  • Xycom ProServer to CJ1 - This document shows how to setup Xycom's ProServer and GP-Pro to connect to an Omron CJ1 and collect data and store it in Excel.
  • Omron CJ1 to Xycom Ethernet - This document will show how to configure the settings on the Omron CJ1 and the Xycom HMI to allow them to communicate over Ethernet.
  • Omron CS1 to Xycom HMI RS422 Using SCB41 Inner Board - This document will show how to configure the settings on a Xycom HMI and Omron SCB41 to make these 2 devices communicate over RS422.
  • ST401 RS232 to 750-842 - This document will show how to configure the settings on the Xycom ST-401 HMI, and show how to configure the settings on the Wago 750-842 Modbus Controller.
  • CJ1W-ETN11 Connection from the internet - This document will show how to configure the settings on the CJ1W-ETN11 Ethernet Module to connect remotely through a router or via the internet.
  • CJ1M-ETN via Adam 4571 RS232 to Ethernet Convertor - This document will show how to configure the settings on the ADAM 4571 RS232 to Ethernet module to allow you to connect to an Omron PLC via Ethernet.
  • NT30 to CS1 SCU41 via Advantech Adam 4522 - This document will show how to get the Omron NT30 operator interface to communicate to the CS1W SCU41 over a distance of up to 1000 feet by using RS422 and the Adam 4522 RS232 to RS422 converter. We will use the RS422 port on the NT30 and the RS232 port on the SCU41.
  • CJ1WCT021 High Speed Counter Module - This document will show how to configure the settings of the CJ1WCT021 high speed counter module.
  • Download Program to NS via Serial Connection to Omron PLC - This document will show how to download to an Omron NS Operator Interface using a Pass Through connection to the Omron CJ1M PLC. The PC will be connected to the PLC using a serial connection and the NS will be connected to the PLC using a serial connection. The PC will then be able to download to the NS via the PLC.
  • Omron Handheld Barcode Reader to Omron NT31C Operator Interface - This document will show how to connect an Omron V520-LGP6125-P Handheld Barcode Reader to the Omron NT31C operator interface.
  • Omron CQM1H to Microscan Barcode Reader via SCB41 - This document will show how to connect an Omron CQM1H PLC to a Microscan MS-850 Barcode Reader using the CQM1H-SCB41 Communications Board and the protocol macro command. The PLC will prompt the MS-850 via ASCII to read and the MS-850 will send the barcode information back to the PLC via ASCII to be stored in DMs.
  • Omron PLC Modem - This document will show how to connect Omron PLC programming software to an Omron PLC via a modem.
  • CQM1H to AxiomPlus - This document will show how to connect an Omron CQM1H PLC over an RS232 cable to a Tolomatic AxiomPlus and change a move to distance inside the AxiomPlus via ASCII commands.
  • CQM1H to Cimrex over TCP/IP - This document will show how to connect and program an Omron CQM1H PLC over a local Ethernet network by using the transparent mode on a Cimrex 30 operator interface as a pass through programming connection.
  • CS1W-SCB41 PMCR to Keyence VG-301 - This document will show how to connect a CS1 PLC to a Keyence VG-301 using a CS1W-SCB41 RS232 module communicating Protocol macro. The PLC will send ASCII commands via the Protocol Macro function to write the Hi and Low Limits in the VG-301.
  • Adam OPC to Machine Edition - This will show how to connect Advantech Adam IO Modules to the GE Machine Edition software using an Advantech OPC server and the GE OPC client.
  • PC to C200HE RS422 - This will show how to connect a PC to a C200HE PLC over a long distance using RS422 communications.
  • CS1W-SCU21 PMCR to E5EN - will show how to connect a CS1 PLC to an E5EN temp controller using a CS1W-SCU21 RS232 module communicating Protocol macro. The PLC will send commands to read and write the set point, alarm 1 and 2 values and the heater burn out values.
  • SLC503 PrecisionAire - A PLC program to control a Tolomatic PrecisionAire Actuator from an Allen Bradley PLC. An example of an automatic lane shifter.
  • CQM1H PrecisionAire - A PLC program to control a Tolomatic PrecisionAire Actuator from an Omron PLC. An example of an automatic lane shifter.
  • OCS to Encoder - This document will show how to wire and program a GE PNP Operator Control Station to an Omron Encoder using the high speed counter inputs.
  • CQM1H to Keyence VG301 - This document will show how to connect a CQM1H Omron PLC to a Keyence VG-301 Laser measurement Sensor and then use the PLC to change the upper and lower set points.
  • CS1 Modem - How to connect to a remote CS1 PLC via a modem.
  • S3S as Motion detector - Using the S3S controller as motion detector for a motor shaft.
  • PC to E5CK RS422 - Sending set points from Hyper terminal to the E5CK using RS422.
  • CS1 Ethernet - How to program a CS1 PLC over an Ethernet Network.
  • CQM1 Absolute Encoder - How to hookup an Absolute Encoder to a CQM1.
  • F150-HE - An F150 Vision system transferring information to a C200HE via RS422.
  • MDROPNT - A C200H alpha talking to up to 8 NT31/31C touch screens through one RS422 port on the COM06 communications board.
  • HS422MAR - A C200HS PLC sending ASCII messages to up to 99 scrolling Marquee message centers via an RS485 network. The C200HS RS232 port is being converted to RS422 by an NT-AL001 converter.
  • HS232MAR - A C200HS PLC sending ASCII messages to a scrolling Marquee message center via an RS232 port.
  • MARQPC - A scrolling Marquee message center being sent messages from a PC.
  • PMCRE5CK - A Protocol Macro Function in a C200H Alpha PLC reading and writing information to up to 99 E5CK Temperature Controllers.
  • VSNPMCR - A Protocol Macro Function in a C200H Alpha PLC reading and writing information to an Omron F300 Vision System.
  • Host Link RS422 - An example of how to communicate from your computer's RS232 port to up to 32 Omron PLCs via an RS422 network.
  • HOSLINPM - A Protocol Macro Function in a C200H Alpha PLC gathering data memory contents from any CQM1 and CPM1 PLCs over an RS422 network.
  • NTPRINT - An example of how to print out of an NT30C touch screen.
  • PWSP2000 - How to collect data from a SensorPulse unit and display it in a Process Windows HMI package.
  • CAPSSWN - The instructions on how to convert a CAPS program into a Syswin Program including Labels.
  • AXICQM1 - A CQM1 PLC controlling a Tolomatic Axidyne linear screw drive actuator.
  • CPM1E2E - How to wire an E2E sensor to a CPM1 PLC in either an NPN or PNP way.
  • NT20IDSC - An example program using an IDSC RFID controller and an NT20S touch screen reading and writing data to a tag.
  • RFNTCQM1 - An example program using a CQM1 PLC sending commands to an Omron stand alone RDID controller. Information is being displayed on an NT20S touch screen.
  • NC112 - An example of a C200H-NC112 stepper control module running a Tolomatic Axidyne and Closed Loop DC Drive Module with pulse and direction inputs.